Battery Types Explained: LiFePO4, Lithium-Ion, Lead-Acid and Solid-State

A battery stores energy chemically and releases it as electricity. For portable power and home backup, four chemistries matter most: LiFePO4, lithium-ion (NMC/NCA), lead-acid, and the emerging solid-state family. LiFePO4 is the default for modern power stations because it lasts longer and is more thermally stable; NMC is lighter; lead-acid is cheaper upfront but heavy and short-lived.

By WhichWatts editorial team · Updated October 25, 2026

Diagram comparing LiFePO4, lithium-ion, lead-acid and solid-state battery chemistries

What is a battery?

A battery converts stored chemical energy into electrical energy. In a rechargeable battery, lithium ions move between an anode and a cathode through an electrolyte while electrons travel through the external circuit.

A single battery cell contains an anode (negative electrode), a cathode (positive electrode), an electrolyte that carries ions, and a separator that keeps the electrodes from touching. Cells are wired in series to raise voltage and in parallel to raise capacity, then packaged as a battery pack with a battery management system (BMS).

The BMS is not optional in a lithium battery. It monitors cell voltage, current, and temperature, balances cells, and disconnects the pack if a cell goes outside its safe operating window. A well-designed pack with a capable BMS is more important than a chemistry label alone.

Capacity is usually written in watt-hours (Wh) for a complete pack and amp-hours (Ah) for a single cell or 12V battery. Watt-hours are the comparable unit: Wh = volts × amp-hours. A 12V 100Ah battery holds about 1,200Wh of nominal energy.

Which battery types matter for power stations and home backup?

Five chemistries cover almost every product you will see: LiFePO4 (LFP), lithium-ion NMC/NCA, lead-acid, lithium titanate (LTO), and solid-state. LFP and NMC dominate portable power stations; lead-acid still appears in budget stationary backup; LTO and solid-state are niche or emerging.

Chemistry Cathode Typical manufacturer-rated cycle life Typical energy density Main strength Main trade-off
LiFePO4 (LFP) Lithium iron phosphate 3,000–5,000 About 90–160 Wh/kg Long life, thermal stability, lower cost per Wh Heavier for the same capacity; cold-charging limits
NMC / NCA Nickel manganese cobalt or nickel cobalt aluminum 500–1,000 About 150–250 Wh/kg High energy density; lighter packs Shorter cycle life; more thermal management
Lead-acid (AGM, gel, flooded) Lead dioxide / sponge lead 300–500 at 50% depth of discharge About 30–50 Wh/kg Low upfront cost; simple Heavy, short-lived, 50% usable capacity
LTO Lithium titanate oxide 10,000+ About 50–80 Wh/kg Very long life; fast charging Low energy density; expensive
Solid-state Solid electrolyte Not yet mainstream Target much higher than liquid lithium-ion Potential safety and density gains Manufacturing cost, interfaces, scale

The ranges are typical manufacturer figures, not guarantees. A 3,000-cycle LFP claim usually means 3,000 full cycles to 80% of original capacity under specific laboratory conditions. Real-world life depends on temperature, depth of discharge, charge rate, and how the pack is stored.

What is LiFePO4 (LFP)?

LiFePO4 is a lithium-ion chemistry with an iron-phosphate cathode. It typically delivers 3,000–5,000 manufacturer-rated cycles, is more thermally stable than NMC, and is heavier for the same capacity. It is the default chemistry for mid-range and premium portable power stations.

LiFePO4 cells have a nominal voltage of about 3.2V. They are popular because the cathode is chemically stable, the cycle life is long, and the raw materials are relatively abundant. The trade-off is lower gravimetric energy density: an LFP pack is usually larger and heavier than an NMC pack of the same watt-hours.

LFP is not immune to cold. Charging below 0°C (32°F) can cause lithium plating, which permanently reduces capacity and creates a safety risk. Many power stations block charging below freezing; some premium units add internal heating. Discharging in cold weather is usually allowed, but available capacity drops.

For a deeper comparison, see the LiFePO4 battery guide.

What is NMC or NCA lithium-ion?

NMC (nickel manganese cobalt) and NCA (nickel cobalt aluminum) are lithium-ion chemistries with higher energy density than LFP. They are lighter and smaller for the same watt-hours, but typically have shorter cycle life and need more thermal management.

NMC and NCA are common in electric vehicles, power tools, and compact power stations where weight and volume matter. “NCM” is the same family as NMC, with the elements written in a different order.

These chemistries typically have a nominal cell voltage of about 3.6–3.7V, so fewer cells are needed for a given pack voltage. They also tend to cost more per kilowatt-hour at the pack level when safety systems and thermal management are included.

NMC is not inherently unsafe. A certified pack with a well-designed BMS, cell spacing, and thermal protection can be used safely. The risk rises when cells are overcharged, overheated, physically damaged, or built without adequate protection.

Is lead-acid still used?

Yes, mostly in budget stationary backup and off-grid systems. Lead-acid is cheap and simple, but heavy, short-lived, and should not be regularly discharged below about 50% of its capacity.

Lead-acid covers flooded, AGM, and gel batteries. They are robust in the sense that they tolerate abuse better than lithium in some ways, but they have low energy density and a limited cycle count. A 100Ah 12V lead-acid battery is often treated as a 50Ah usable battery because repeated deep discharge shortens its life.

Lead-acid is still a reasonable choice for a stationary, infrequently cycled system where upfront cost and simple charging matter more than weight or longevity. For a portable power station, it is usually the wrong trade-off: the weight is high and the usable capacity is low.

What is LTO?

Lithium titanate oxide is a niche lithium-ion chemistry with very long cycle life and fast charging, but low energy density and high cost. It is rare in consumer power stations.

LTO cells use a lithium titanate anode instead of graphite. They can charge quickly and tolerate many more cycles than conventional lithium-ion cells, which makes them attractive for buses, grid buffers, and applications where uptime matters more than weight.

The trade-off is low cell voltage (about 2.4V) and low energy density, so an LTO pack is bulky for its capacity. You may see LTO mentioned in marketing, but it is not a mainstream choice for portable power stations.

Are solid-state batteries available?

Not in mainstream portable power stations as of 2026. Solid-state cells replace the liquid electrolyte with a solid one, promising higher energy density and better safety, but manufacturing cost, interface resistance, and scale remain unresolved.

Solid-state is a family of designs, not a single chemistry. Some use a sulfide, oxide, or polymer electrolyte; some still use a lithium-metal anode. The common claim is a higher energy density and a lower fire risk than liquid-electrolyte lithium-ion.

Automotive companies and battery startups have announced pilot lines and production targets, but announcements are not the same as shipping consumer products. Before buying any product advertised as solid-state, check the cell datasheet, the warranty, and whether the chemistry is actually solid-state or a semi-solid or liquid-electrolyte design.

For the current status of shipping products, see the solid-state power station guide.

Which battery type is best for a power station?

For most buyers, LiFePO4 is the best default: it lasts longer, is more thermally stable, and now has a lower median cost per watt-hour in the WhichWatts catalog. Choose NMC/NCA when weight or compact size matters more than cycle life; choose lead-acid only for a stationary, low-cost, infrequently cycled system.

A practical decision order:

  1. Start with LiFePO4 unless you have a specific reason to avoid it. It covers camping, RV, home backup, and daily cycling well.
  2. Choose NMC/NCA for a compact or lightweight station where the extra energy density is worth a shorter cycle life.
  3. Choose lead-acid only for a stationary budget system with low cycle use and enough space for the weight.
  4. Do not pay a premium for “solid-state” in a portable power station in 2026 unless the product is shipping, certified, and independently verified.

The chemistry is only one part of the decision. Output power, surge capability, solar input, ports, weight, warranty, and the quality of the BMS matter just as much.

Which battery type is best for home storage?

LiFePO4 dominates new home storage because of cycle life, thermal stability, and cost. Check inverter compatibility, usable capacity, warranty, depth of discharge, and installation requirements rather than relying on the chemistry label alone.

Home storage systems are usually purchased as a complete package: battery, inverter, monitoring, and installation. The battery chemistry affects longevity and safety, but the system design determines how much of the advertised capacity you can actually use.

Ask for the usable capacity in kWh, the round-trip efficiency, the maximum continuous charge and discharge power, the warranty throughput, and the backup transfer time. A 10kWh battery with a 90% depth of discharge and 90% round-trip efficiency does not deliver 10kWh to your loads.

How do I read a battery spec sheet?

Start with chemistry, nominal voltage, capacity in Wh, usable capacity, cycle life and the depth of discharge it is rated at, continuous charge and discharge power, temperature limits, and warranty. Ignore cycle-life claims that do not state the end-of-life capacity and test conditions.

A useful checklist:

  • Chemistry and cell format: LFP, NMC, NCA, LTO, or lead-acid; prismatic, cylindrical, or pouch.
  • Nominal voltage and capacity: Wh is comparable; Ah needs a voltage to mean anything.
  • Usable capacity: the kWh or Wh you can actually draw, after depth of discharge and system limits.
  • Cycle life: “3,000 cycles to 80%” is meaningful; “3,000 cycles” without an end-of-life threshold is not.
  • Continuous and peak power: the inverter limit, not just the battery limit.
  • Charge and discharge temperature range: especially the minimum charging temperature.
  • Warranty: years, throughput, and what voids coverage.
  • Certification: UL 2743 or IEC 62619 for power stations, UN 38.3 for transport, and local electrical approvals where relevant.

Bottom line

LiFePO4 is the safest default for portable power and home backup in 2026. NMC/NCA is the lighter, more compact option; lead-acid is a budget stationary choice; LTO and solid-state are not mainstream consumer options yet.

If you are choosing between two power stations with similar capacity and output, prefer the one with a reputable BMS, a clear warranty, and a chemistry that matches how often you will cycle it. For most buyers, that means LiFePO4.

Where to start shopping

The three lowest cost-per-watt-hour stations in the live US catalog. Affiliate links; the ranking is not paid.

Retailer links are affiliate links. WhichWatts may earn a commission; the shortlist is ranked by cost per watt-hour, not by commission.

Shop by brand

Direct links to manufacturer stores. These are affiliate links and we may earn a commission.

Bluetti · EcoFlow · Anker Solix · Jackery · Pecron · Renogy

Compare before you buy

Browse every model · Cost per watt-hour chart · Best for home backup · Size a system for your appliances

Common questions

Is LiFePO4 better than lithium-ion?

LiFePO4 is a type of lithium-ion battery. Compared with NMC/NCA lithium-ion, LFP usually lasts longer and is more thermally stable, but it is heavier for the same capacity. The better choice depends on whether you value cycle life and safety or weight and compact size.

How long do batteries last?

Cycle life and calendar life both matter. A LiFePO4 power station is typically rated for 3,000–5,000 cycles to 80% capacity; NMC is typically 500–1,000. Even when unused, lithium batteries age, especially when stored hot or at a full charge. Five to ten years is a reasonable planning range for a well-treated power station.

What is the difference between Wh and Ah?

Watt-hours equal volts multiplied by amp-hours. A 12V 100Ah battery stores about 1,200Wh. Amp-hours alone are not comparable across different voltages, so use watt-hours when comparing power stations.

Are solid-state batteries available in power stations?

Not in mainstream portable power stations as of 2026. Solid-state cells are in automotive development and pilot production. Be skeptical of consumer products that use “solid-state” loosely without a cell datasheet or independent verification.

Is lead-acid still worth it?

Only for a stationary, low-cost system with infrequent cycling and enough space for the weight. For portable use, lithium’s usable capacity, weight, and cycle life usually outweigh the lower sticker price.

What is depth of discharge?

Depth of discharge (DoD) is the percentage of a battery’s capacity you use before recharging. Lead-acid is usually limited to about 50% DoD for good life; lithium can often use 80–100%, although staying around 80% for daily cycling can improve longevity.

Sources

Related: Lithium-ion battery: how it works · LiFePO4 battery: cycle life and trade-offs · Battery capacity explained · Solid-state batteries: status and trade-offs · Compare portable power stations · Best power stations for home backup

WhichWatts is independent and funded by affiliate commission. Figures come from manufacturer specifications and the live catalog; see our methodology. Corrections to hello@whichwatts.com.