Battery Capacity Explained: Wh, Ah, kWh and Usable Capacity

Battery capacity is the amount of energy a battery can store, usually measured in watt-hours (Wh) or kilowatt-hours (kWh). Nameplate capacity is not the same as usable capacity: depth of discharge, inverter efficiency, temperature, and aging all reduce the energy you can actually draw. To size a system, add up your loads in watts, multiply by hours, and add a 20% buffer.

By WhichWatts editorial team · Updated October 25, 2026

Comparison of battery capacity and usable energy by chemistry

What is the difference between Wh, Ah and kWh?

Watt-hours measure energy; amp-hours measure charge. To compare batteries at different voltages, convert Ah to Wh by multiplying by volts. 1 kWh equals 1,000 Wh.

Unit What it measures Formula Example
Amp-hour (Ah) Charge Current × time A 100Ah battery can supply 5A for 20 hours in theory
Watt-hour (Wh) Energy Volts × amp-hours 12V × 100Ah = 1,200Wh
Kilowatt-hour (kWh) Energy Wh ÷ 1,000 1,200Wh = 1.2kWh

A 12V 100Ah battery and a 24V 50Ah battery both hold about 1,200Wh, but they are not interchangeable: the 24V pack needs a different charger and inverter. Always check the system voltage before comparing Ah ratings.

Portable power stations usually quote Wh directly. Home batteries quote kWh. Solar panels quote watts (instantaneous power), not watt-hours.

What is usable capacity?

Usable capacity is the energy you can actually draw from a battery after respecting its depth-of-discharge limit and accounting for conversion losses. It is always lower than the nameplate capacity.

A 1,000Wh power station does not run a 100W load for exactly 10 hours. The inverter converts DC battery voltage to AC with some loss, the BMS may reserve a small buffer at the top and bottom, and the battery’s available capacity drops as it ages and cools.

A more realistic estimate is:

Runtime (hours) = usable Wh × inverter efficiency ÷ load watts

For a 1,000Wh station with 85% efficiency and a 100W load: 1,000 × 0.85 ÷ 100 = 8.5 hours. That is an estimate, not a guarantee. The actual runtime depends on the load’s power factor, the inverter’s efficiency curve, and the battery’s condition.

What is depth of discharge?

Depth of discharge (DoD) is the percentage of a battery’s capacity you use before recharging. Lead-acid is usually limited to about 50% for good life; lithium can often use 80–100%, although shallower cycles can improve longevity.

A 100Ah lead-acid battery discharged to 50% DoD gives about 50Ah of usable capacity. Discharging it to 80% regularly will shorten its life. That is why lead-acid systems are often specified with twice the nominal capacity of a lithium system serving the same load.

Lithium is more tolerant of deep discharge, but not immune. Many manufacturers rate cycle life at 80% DoD or 100% DoD; the same battery may last longer at 80%. If the spec sheet does not state the DoD used for the cycle-life claim, the number is hard to compare.

What losses reduce usable capacity?

Inverter conversion, wiring resistance, battery internal resistance, temperature, and aging all reduce the energy delivered to your devices. A 10–15% total loss is a reasonable planning assumption for a portable power station.

The biggest loss is usually the inverter: converting DC to AC is typically 85–90% efficient, and efficiency drops at very low loads. DC outputs (USB, 12V) avoid the inverter loss and are more efficient for compatible devices.

Temperature matters too. Lithium capacity falls in cold weather, and charging is restricted below freezing. Aging reduces capacity gradually; a battery at 80% state of health has 20% less usable energy than when new.

For planning, add a 20% buffer to your calculated watt-hours. That covers inverter losses, aging, and the fact that most loads are not perfectly constant.

How do I calculate the capacity I need?

List each device’s wattage, multiply by the hours you need it, add the results, and multiply by 1.2 for losses and aging. Then choose a battery whose usable capacity meets or exceeds that total.

Example: a camping trip with a 50W laptop for 4 hours, a 10W phone charger for 3 hours, and a 30W light for 5 hours.

  • Laptop: 50W × 4h = 200Wh
  • Phone: 10W × 3h = 30Wh
  • Light: 30W × 5h = 150Wh
  • Total: 380Wh
  • With a 20% buffer: 380 × 1.2 = 456Wh

A 500Wh station is the minimum; a 700–1,000Wh station gives more headroom and lets you run a small fridge or a fan. Use the power station calculator to model your own list.

How many batteries do I need?

Divide your total required watt-hours by the usable watt-hours per battery. Usable watt-hours = nominal watt-hours × depth of discharge × inverter efficiency. Round up to the next whole battery.

Example: you need 2,400Wh for a small fridge and lights.

Lithium 12V 100Ah battery: 1,200Wh nominal × 90% DoD × 90% inverter efficiency = about 972Wh usable. 2,400 ÷ 972 = 2.47, so you need 3 batteries.

Lead-acid 12V 100Ah battery: 1,200Wh nominal × 50% DoD × 90% efficiency = about 540Wh usable. 2,400 ÷ 540 = 4.44, so you need 5 batteries.

This is why lead-acid systems look cheap per battery but cost more per usable watt-hour. The same math applies to portable power stations: use the station’s usable capacity, not just the nameplate Wh.

How long will a power station run my devices?

Use the runtime formula: usable Wh × inverter efficiency ÷ load watts. The table below shows estimates for 500Wh, 1,000Wh and 2,000Wh stations at common loads, assuming 85% inverter efficiency and a new battery.

Load 500Wh station 1,000Wh station 2,000Wh station
50W About 8.5 hours About 17 hours About 34 hours
100W About 4.3 hours About 8.5 hours About 17 hours
300W About 1.4 hours About 2.8 hours About 5.7 hours
500W About 0.9 hours About 1.7 hours About 3.4 hours

These are estimates. A fridge cycles on and off, so its average draw is lower than its running wattage; a motor or compressor may need a surge well above its running watts. Check the station’s continuous and peak output before connecting a load.

How does capacity affect cost per watt-hour?

Larger batteries usually cost less per watt-hour than smaller ones, but the relationship is not linear. In the current WhichWatts catalog, sub-500Wh stations have the highest median $/Wh and 2,000Wh+ stations have the lowest.

Small stations carry a higher share of fixed costs: the inverter, ports, display, enclosure, and packaging are spread over fewer watt-hours. Large stations benefit from economies of scale, but they also add weight and may include more expensive high-power electronics.

Use the live table on this page to see the current medians by capacity band, then compare specific models. A larger station is not automatically a better value if you do not need the capacity or cannot lift it.

Bottom line

Capacity is energy, not runtime. Convert Ah to Wh, subtract the losses you cannot avoid, and size from your actual loads with a 20% buffer. For most buyers, a 1,000–2,000Wh LiFePO4 station covers camping, short outages, and portable use; larger home backup needs a different system design.

If you are unsure, start with the load list and the calculator, then compare products by usable capacity and cost per watt-hour. Do not buy on nameplate Wh alone.

Where to start shopping

The three lowest cost-per-watt-hour stations in the live US catalog. Affiliate links; the ranking is not paid.

Retailer links are affiliate links. WhichWatts may earn a commission; the shortlist is ranked by cost per watt-hour, not by commission.

Shop by brand

Direct links to manufacturer stores. These are affiliate links and we may earn a commission.

Bluetti · EcoFlow · Anker Solix · Jackery · Pecron · Renogy

Compare before you buy

Browse every model · Cost per watt-hour chart · Best for home backup · Size a system for your appliances

Common questions

How many batteries do I need?

Divide your total required watt-hours by the usable watt-hours per battery. For a 2,400Wh load, a 12V 100Ah lithium battery with 90% depth of discharge and 90% inverter efficiency provides about 972Wh usable, so you need 3. A lead-acid battery at 50% DoD provides about 540Wh, so you need 5.

What is the difference between Wh and Ah?

Watt-hours measure energy; amp-hours measure charge. Wh = volts × Ah. A 12V 100Ah battery is about 1,200Wh. You cannot compare Ah ratings across different voltages without converting them.

What is usable capacity?

Usable capacity is the energy you can actually draw after respecting the depth-of-discharge limit and accounting for inverter and wiring losses. It is always lower than the nameplate capacity.

How long will a 1,000Wh power station run a fridge?

It depends on the fridge’s running wattage and duty cycle. A small fridge drawing 60W with a 50% duty cycle uses about 720Wh per day, so a 1,000Wh station with 85% efficiency could run it for roughly one day. A full-size fridge may exceed the station’s capacity or surge rating.

Is a bigger battery always better?

No. A larger battery costs more, weighs more, and takes longer to recharge. Size for your actual loads with some headroom; do not buy capacity you will never use.

Can I add batteries later?

Some power stations support expansion batteries; many do not. Check the product specifications before buying if expandability matters. Mixing different battery ages or chemistries in a DIY system can be unsafe.

Sources

Related: Battery types explained · Lithium-ion battery guide · LiFePO4 battery guide · Battery backup sizing · Solar battery storage · Power station runtime guide · Size your system with the calculator

WhichWatts is independent and funded by affiliate commission. Figures come from manufacturer specifications and the live catalog; see our methodology. Corrections to hello@whichwatts.com.